Skip to content
Institute For Sustainable Forestry

Latest News and Information

Biochar

“Heat Doesn’t Rise, and Wood Doesn’t Burn”

2020-05-02
By: isf_admin1
On: May 2, 2020
In: Documents & Articles
With: 0 Comments

“Heat Doesn’t Rise, and Wood Doesn’t Burn”

by Gray Shaw, April 2020

Woody plant waste comes in many shapes and sizes and conditions. On April 8, we assembled all the brush and wood that Chip had lying around and made biochar.

Some of the material was good for starting the fire. Some was acceptable later in the burn. And some was not suitable at all.

We also filmed the event, to show others how to make decisions about what to use and how.

Chip was using an Oregon kiln, designed by Kelpie Wilson. This kiln is simply an open box with sloped walls and a drain. Its purpose is to control air flow to the pile so that air only enters at the top. There’s a drain plug to empty the water after you quench the fire. You can make a pile on the open ground, and it will work almost as well.

When we arrived, Chip had already loaded his Oregon kiln. But there were problems with Chip’s pile.

Biochar Workshop

First, the material was not arranged so that the fire could be lit on top and burn down. Biochar piles need small fuel at the top to start, with a gradual size increase as you go down. Large material can be on the bottom or added later. This is upside-down to most people. You probably learned to light a fire at the bottom. Why do we build the fire upside-down? To eliminate smoke and ash, and increase charcoal production. Even if you weren’t trying to make charcoal, this way is better in terms of smoke.

Second, there was too much air space in the pile. In a conventional wood fire, flames ignite the fuel above. In biochar piles, we rely on radiation from the burning fuel on top to ignite the fuel below it, and so on down through the pile. You may have been taught that heat rises. Wrong! Hot air rises, but heat radiates equally in all directions. This is how fire spreads through a biochar pile. In order to catch, the fuel can’t be too far from the burning material above it. There also should not be too big a jump in size between layers.

So we took apart Chip’s pile and rebuilt it. Wood over 3″ diameter was removed. Branches less than 3″ went on the bottom, followed by smaller branches, then twigs, then fine twigs and straw surrounding a paper top knot. The material was closely packed, allowing only enough air space to feed the flames. It really did look like an upside-down fire!

Biochar Workshop

All the material was dry. No green or rotten wood was included.

Anyone who has built a bonfire knows that green material can be put on after the fire gets going. Biochar piles are no exception. However, it slows down the burn temporarily and makes more smoke. The water inside the wood has to evaporate before the wood can burn, and this takes energy away from the fire, which results in smoke. We waited until the fire was really going before adding green material.

Rotten wood can also be added to an established fire. However, rotting is the same as burning, chemically speaking, so there is less fuel left to burn in a rotten limb. The energy released by fire is the same energy consumed by organisms eating the wood. You won’t get as much heat when rotten wood burns. You’ll get more smoke instead. We tossed Chip’s rotten wood into the forest, where it will soon become soil. It wouldn’t contribute much fuel to a wildfire, either.

Biochar Workshop

I lit the fine material and paper, and we watched carefully as the fire grew. If you’ve never seen this before, it’s really quite interesting. Embers drop through the pile while it’s being heated from above, which accelerates the ignition. But because we lit it on top, there was hardly any smoke. We could stand comfortably right next to the pile.

I gently stirred the fire as it burned downward, to make sure all the wood was ignited. Once the fire reached the bottom of the kiln and flames began to subside, we began adding fuel, a little at a time.

When adding fuel, we try to maintain a “flame cap” over the pile by adding just enough fuel to feed the flames. Too much at a time makes smoke. When ashes began to form on a part of the fire, we quickly place new fuel there. We keep this up until we run out of fuel or space in the kiln, whichever happens first. Then we wait until the flames go out and extinguish the pile with water.

How does this flame cap work?

Charcoal is what’s left over when all the compounds containing hydrogen and oxygen are driven out of the wood as gases, along with some carbon particles. Together, these “volatiles” are what burns as flame. They burn in the air, whereas charcoal burns where it is. As long as we keep air from reaching the wood, charcoal will build up at the bottom of the fire. The kiln controls the air so that it only enters the fire at the top; that’s mainly what it’s for. The burning flames extend across the top of the pile, forming a cap that keeps oxygen away from the wood. The heat of this combustion keeps driving volatiles out of the wood until they’re all released. Smoke is the particles that escape combustion. The flames keep air from touching the wood directly.

Biochar Workshop

In other words, wood doesn’t burn. It separates into volatiles and charcoal, which burn separately. In an ordinary fire, of course, some air can reach the wood and some charcoal is burned along with the volatiles, but it still tends to burn last. When your campfire goes out, instead of enjoying the glowing coals, you could stop the fire with water and you’d have charcoal.

We had many different fuels to throw on. Chip had been saving up branches and stems of various soft and hardwood species for awhile, and he cut some green material just for the occasion. We even had an old bamboo screen woven together with wire. The wire was easily removed after the fire was out.

When you make biochar, you want all the material to finish flaming at about the same time. If bigger pieces are added too late, the smaller branches will flame out first and start turning to ash before the bigger ones are done. It’s best to set aside a quantity of smaller material to add at the end, so that any larger unburned pieces can catch up.

Lest you be tempted to burn lumber or agricultural waste, bear in mind that there are prohibitions in place about those. Old pressure-treated lumber contains chromated copper arsenic (CCA), and newer PT lumber still has high copper levels. You don’t want that in your soil. All construction debris is illegal to burn. The rule about ag waste is a good thing for the CA central valley, where smoke from burning rice straw used to obscure visibility and injure lungs on I-5. Air quality management districts have not yet made exceptions for clean-burning biochar manufacture.

Leaves and grasses burn too, of course, as long as they’re not matted together. Air flow is limited by matting, which causes smoke. Leaves tend to fly off as embers. Just to demonstrate this, I threw on some matted leaves and grass. Once was enough!

Biochar Workshop

At the end, we flooded the kiln to extinguish the burn. When all the coals were out, we pulled the plug and drained the kiln (a nice feature to have). The yield was about 15 to 20 percent of the volume of brush we added.

Biochar Workshop

This charcoal will need to receive two treatments before being used as a soil amendment. First, it needs to be reduced in size to 1/4″ or less. Larger pieces will not be easily penetrated to the center by water, nutrients, organisms and root hairs. Second, it should be inoculated with compost, worm castings, or compost tea. Otherwise, it will draw nutrients from the soil, reducing productivity, until it becomes fully charged.

You don’t need a kiln to make biochar. Kilns are used to control air flow, which increases efficiency, reduces smoke, and lets you stand closer to the fire. You can simply make a pile on open ground, being careful to scrape away flammable material down to mineral soil around the pile. You will get about a 10 percent yield. If your primary objective is fuel reduction, the biochar becomes a side benefit.

All you need for good biochar is biomass and a match. But be safe! Clear your perimeter beforehand and have water ready.

Biochar Workshop, March 13, 2020

2020-03-28
By: isf_admin1
On: March 28, 2020
In: ISF Events
With: 0 Comments

Biochar Workshop, March 13, 2020, Miranda, CA

with T. Gray Shaw and Susan Nolan

On Friday March 13, 2020 Gray Shaw and Susan Nolan of the Institute for Sustainable Forestry presented an afternoon workshop on making and using biochar from forest waste resulting from fuel reduction. The site was Lonnie Whitlow’s Workhorse Welding shop in Miranda. Lonnie built a 4’x4′ biochar kiln last year for ISF and offers to make more on request.

Susan built a top-lit fire in her mini-kiln while Gray explained the process and answered questions.

Gray’s farmer/neighbor Ingrid Leon explained biochar inoculation and the results from adding 5% biochar to the soil in 2019: 25% less water use, healthier plants, and double productivity. Gray demonstrated his homemade charcoal grinder, which makes 1/4″ biochar from forest waste. This hand-powered grinder processed all the char for 10,000 square feet of garden.

For the full story leading to this workshop, see www.blackripple.com.

Biochar Workshop, 3/13/2020
Biochar Workshop, 3/13/2020
Biochar Workshop, 3/13/2020
Biochar Workshop, 3/13/2020
Biochar Workshop, 3/13/2020
Biochar Workshop, 3/13/2020
Biochar Workshop, 3/13/2020
Biochar Workshop, 3/13/2020
Biochar Workshop, 3/13/2020
Biochar Workshop, 3/13/2020
Biochar Workshop, 3/13/2020
Biochar Workshop, 3/13/2020
Biochar Workshop, 3/13/2020
Biochar Workshop, 3/13/2020
Biochar Workshop, 3/13/2020
Biochar Workshop, 3/13/2020
Biochar Workshop, 3/13/2020
Biochar Workshop, 3/13/2020

 

AUDIO: ISF Radio Hour on KMUD 12/30/19

2020-01-23
By: isf_admin1
On: January 23, 2020
In: Sustainable Forestry Journalism Project
With: 0 Comments

ISF Radio Hour on KMUD, 12/30/19

Chip Tittmann and Gray Shaw discuss biochar and sustainable forestry in the latest monthly installment of ISF hour. Special guest David Simpson talks about Rainbow Ridge. ISF Radio Hour airs on “Monday Night Talk” at 7PM on the fifth Monday of the month on KMUD radio, 91.1 FM / kmud.org

http://blog.instituteforsustainableforestry.com/wp-content/uploads/2020/01/kmud_191230.mp3

 

 

Recent Posts

  • A Visit to K-P & Sons Mill
  • Audio: Sustainable Forestry Journalism Project: 3/17/21
  • Audio: Sustainable Forestry Journalism Project: 3/3/21
  • Audio: Sustainable Forestry Journalism Project: 2/3/21
  • Audio: Sustainable Forestry Journalism Project: 1/27/21

Recent Comments

  • Linda Paine on A Visit to K-P & Sons Mill
  • Embracing Fire 2019 – Institute For Sustainable Forestry on Photos from FIRED UP Dec 8, 2018
  • A WordPress Commenter on ISF and Garberville Rotary Present: ALL FIRED UP!  2018

Archives

  • September 2021
  • March 2021
  • February 2021
  • January 2021
  • December 2020
  • November 2020
  • September 2020
  • August 2020
  • July 2020
  • June 2020
  • May 2020
  • April 2020
  • March 2020
  • February 2020
  • January 2020
  • October 2019
  • May 2019
  • April 2019
  • March 2019
  • December 2018
  • November 2018
  • October 2018
  • September 2018

Categories

  • Documents & Articles
  • ISF Events
  • Sustainable Forestry Journalism Project

Meta

  • Log in
  • Entries feed
  • Comments feed
  • WordPress.org

Designed using Dispatch WordPress Theme. Powered by WordPress.